You just recorded a two-minute investor update in a quiet parked car. On playback you hear lip smacks and wet clicks between sentences, and you start wondering whether to scrap it and record again.
That instinct makes sense. Mouth noise is small, but on a phone mic it sounds like hesitation, and it pulls attention away from your message. The bigger cost is the re-record loop, where each new take fixes one flaw and adds another.
This guide shows you how to remove mouth clicks from voice message recordings while keeping your voice, accent, and cadence intact. You'll learn what causes clicks, how to prevent most of them, and which cleanup method fits each type of message. One finding may surprise you: the DAW fix most tutorials recommend is overkill for a 60-second message. If you send voice notes for founders, investors, or clients, this applies directly to you.
Mouth clicks come from saliva, dry mouth, lip contact, and holding the mic too close. Prevent most of them before you record, then remove the rest with one automatic cleanup pass. The outcome is a clean message in one take. All you need is your phone mic and a recorded or ready-to-record message, with no DAW skills required.
What Causes Mouth Clicks and How Do You Stop Them Before Recording?
A mouth click is a short, sharp sound made when saliva and your tongue separate inside your mouth. A lip smack is the sound of your lips parting before or between words. Both come from dry mouth, sticky saliva, lip contact, and holding the phone too close.
You can prevent most clicks without editing software. Use these four steps before a phone recording:
- Hydrate with water. Dry mouth is the most common cause of clicks because saliva gets thick and tacky. Sip room-temperature water a few minutes before you record and keep a glass nearby.
- Skip dairy and sugary drinks. Voice-over performers commonly avoid milk, coffee with cream, and soda right before a session because these drinks can leave saliva sticky. If you just had one, rinse with water before you hit record.
- Relax your jaw and lips. Tension makes your lips press together and peel apart, which creates smacks at the start of sentences. Roll your shoulders, let your jaw drop slightly, and breathe through your nose between phrases.
- Set your mic distance. A phone held against your mouth picks up every wet sound in close detail. Hold it about a hand's width away so your voice stays clear and mouth noise fades.
Pro tip: Angle the phone mic slightly off-axis from your mouth, pointing it toward your chin or cheek. Plosives and clicks then pass the mic instead of hitting it directly.
Prevention handles the biggest causes. VClar can then reduce leftover mouth clicks, breath sounds, and background noise, and it can also remove filler words from audio in the same pass.
But here's the catch: prevention never removes every click.

Automatic Cleanup vs. Manual Editing, Which Should You Use?
Use automatic cleanup for most voice messages and save manual editing for finished audio products. Base the choice on two things: how much is riding on the message and how long it is.
| Message type | Typical length | Stakes | Recommended method |
|---|---|---|---|
| Casual (team, friends) | Short | Low | Prevention only |
| Client update | Short to medium | Medium | Automatic cleanup |
| Investor update | Short to medium | High | Automatic cleanup |
| Translated message | Any | Medium to high | Automatic cleanup, then translation |
| Podcast or voiceover deliverable | Long | High | Manual DAW editing |
Manual tools are strong at what they do. Editing waveforms in Logic Pro's file editor and running iZotope repair modules give podcasters and voice actors precise, click-by-click control. Both take time to learn, though, and each fix happens by hand.
- Prevention only: Best for casual team messages where a stray click won't change how the message lands.
- Automatic cleanup: Best for founders, sales reps, and freelancers who need a polished message in one take. This is also the right step before translating a message.
- Descript-style timeline editing: Best for creators who want to edit through a transcript and revise their content. See VClar vs. Descript for the differences.
- Manual DAW editing: Best for audio engineers and voice actors delivering long-form, broadcast-quality files.
Manual spectral repair is overkill for a quick message someone will hear once. Here's how to clean one in a few steps.

How to Remove Mouth Clicks From a Recorded Voice Message Step by Step
To remove mouth clicks from a voice message, upload or record it, run one cleanup pass, compare the original and cleaned versions side by side, and send. This four-step workflow is built for 30-90 second chat-style messages and usually takes a few minutes from upload to send.
What you need: your recorded message or a mic to record a new one, access to VClar, and the phone or headphones you normally listen on.
- Upload or record the message. Upload the raw voice memo you already made, or record a fresh one directly. Your audio loads and is ready for cleanup in under a minute.
- Run one cleanup pass. Apply cleanup to reduce mouth clicks, breath sounds, and background noise while your natural tone, accent, and rhythm stay intact. You should hear a cleaner version that still sounds like you.
- Compare both versions side by side. Play the original, then the cleaned version, listening for harsh clicks and for any change in your delivery. This is your built-in quality check, and it takes about twice the message length.
- Send the cleaned message. Share the cleaned version through your usual chat app. Your recipient hears one confident take, and you skip the re-record loop.
If clicks aren't the only issue, stack fixes in the same pass. Add filler-word removal for ums and false starts, and fix grammar in your voice message when a sentence came out tangled.
Consider a B2B sales rep following up with an enterprise buyer after a demo. Her 60-second recap is solid but full of wet clicks, so she cleans the existing take instead of recording it a fourth time and keeps her natural, credible delivery.
How do I remove mouth clicks from a voice message? Load the recording into an AI voice cleanup tool like VClar and run a single cleanup pass that reduces mouth clicks, breath sounds, and background noise without replacing your voice, so your tone, accent, and rhythm stay intact. Then play the original and cleaned versions back to back to confirm the harsh clicks are gone and you still sound like yourself before you hit send. For a full polish in one pass, combine click reduction with filler-word removal and spoken-grammar correction.
If you keep re-recording 30-second messages because of clicks and ums, clean your existing take with VClar and send it in one go.

How Do You Know the Cleanup Worked Without Sounding Robotic?
The cleanup worked if harsh clicks are gone and your tone, accent, and rhythm still sound like you. Aim for natural, not zero clicks.
Mouth-click removal is the process of reducing the sharp, wet sounds your lips and tongue make so the voice itself stays untouched. Think of it like wiping smudges off a window rather than replacing the glass.
Here's where most people go wrong: they chase total silence between words. Many voice-over pros treat some mouth sounds as something you can't live without, because over-processing strips cadence, the natural rise and fall of your speech.
Will removing mouth clicks make me sound robotic? Not if the cleanup follows a "keep the voice, drop the noise" principle. VClar reduces mouth clicks, breath sounds, and background noise while preserving your natural tone, accent, and rhythm, so the result is your own voice with fewer distractions, not a synthetic clone. Robotic audio usually comes from aggressive processing that erases every soft sound, and a few gentle mouth noises actually read as human.
To check, play both versions on the phone speaker your recipient will likely use.
- Clicks remain: re-check your mic distance and run cleanup again.
- Voice sounds thin: the original was likely recorded too far from the mic or too far off-axis.
- Noise floor jumps between phrases: record in one consistent environment.
For cross-border messages, clean first, then translate the cleaned voice note so clicks never carry into the translation.
Send Your Next Voice Message in One Take
You don't need a perfect take to send a polished voice message. A good-enough take plus one cleanup pass is all it takes to break the re-record loop.
Picture an independent freelancer sending a weekly client update. She sips water and angles her phone mic before recording, which prevents most clicks at the source, then cleans the rest in one pass and sends her first take.
Your four-point action plan:
- Prevent: hydrate and set your mic distance before you speak.
- Choose: use the comparison matrix to pick automatic cleanup or manual editing.
- Clean: run one pass that also handles fillers and grammar if needed.
- Check: verify by ear on the recipient's likely device.
Your next step is simple: record your next message as you normally would, then clean your next voice message with VClar before you send it. Speak once, sound clear, and spend that saved time on the work that matters.